|
Order Track System Below
FREE SHIPPING |
|
This is a track changer allowing you to switch track from
one direction to the other. A
45°
Changer will turn
45°
and stop. A
90°
Changer will turn
90°
and stop. |
|
 |
|
|
|
76
Meter Tracks
The
76 meter tracks must be supported by a bracket every
36 inches and has should only be used with the Voyager
420, The V4, The Portable Voyager, The V3 or The Griffin.
All track sections include all required bracket's, End
Stop's, Trolley's, Track Brackets and hardware required to
install them. |
|
 |
|
|
|
144
Meter Tracks
The
144 meter tracks can span a 19.6 Ft distance with only
support on each end.
Use with the Voyager
420, 550, 800, V-3, V-4, The Portable and the Griffin.
All track sections include all required bracket's, End
Stop's, Trolley's, Track Bracket's and hardware required
to install them. |
|
 |
|
|
|
30 Degree Curve
All track sections include all required bracket's,
spacers, washers and hardware
required to install them. |
|
 |
|
|
|
45
Degree Curve
All track sections include all required bracket's,
spacers, washers and hardware
required to install them.
|
|
 |
|
|
|
70 Degree Curve
All track sections include all required bracket's,
spacers, washers and hardware
required to install them. |
|
 |
|
|
|
90
Degree Curve
All track sections include all required bracket's,
spacers, washers and hardware
required to install them.
|
|
 |
|
|
|
Pivoting Wall Bracket
The Pivoting Wall Bracket allows you to support the
rail from a wall instead of the ceiling. This Bracket
requires
wall modifications as it is
meant to be bolted to two
2 X 4 studs. |
|
 |
|
|
|
Wall Post & Bracket
The Wall Post Bracket allows you to support the rail from
a wall instead of the ceiling. This
post extends to the floor
providing little strain on the
wall and bearing most of the weight or support from the
floor. |
|
 |
|
|
|
End Stop
The End Stop is used at the
end of a rail run to cap off
and secure the end to stop
the lift when it reaches the
end.
|
|
 |
|
|
|
End Rail Charger
The End Rail Charger serves
to uses. 1st it serves as a
End Stop 2nd it serves as
a automatic charger for the
lift. ( Please Note ) that you
automatically receive one of
these with the purchase of
your lift. |
|
 |
|
|
|
Standard Track Bracket
The Standard Track Bracket
is used to support rail to the ceiling. They are secured
to the ceiling using a 3" Inch lag
bolt. ( Please Note ) that you
automatically receive all the
brackets you will require with each section of rail
ordered
above. |
|
 |
|
|
|
Long Track Bracket
The Long Track Bracket
is used to connect two rails together. This bracket is not
an absolute requirement. Many installations are done using
only stand brackets. |
|
 |
|
|
|
Cathedral Bracket
The Cathedral Bracket
is used for slanted ceilings. Additional brackets or
support may be needed with this type
of application. |
|
 |
|
|
|
Visible Lateral Brace
The Visible Lateral Brace is used to support the rail by
picking up support from 0
to 90 degree angle off a wall
or the ceiling. |
|
 |
|
|
|
Adjustable Lateral Brace
The Adjustable Lateral Brace is used to support the rail
by picking up support from a 0
to 90 degree angle off a wall
or the ceiling. |
|
 |
|
|
|
Track Junction
The Track Junction is used to
connect support (3) track's at (1) point this is used with
the
Portable Voyager or (2) Standard Voyager Lifts. The
only other time this bracket is used is when you simply
want to use a section of rail to pick up support 90
degrees to the side. |
|
 |
|
|
|
Joint Kit
The Joint Kit is used to add support to the joining of two
rails however is not required and offers more of a
cosmetic service. |
|
 |
|
|
|
Long Joint Kit
The Long Joint Kit is used to add support to the joining
of two rails as is the standard joint kit however the long
kit gives added support to the joining of the two rails.
Again is not required. |
|
 |
|
|
|
Reverse Bracket
The Reverse Bracket with Joint Kit Is used when you are
using a turn. The turning rail can be used to go in ether
direction yet
the teeth change direction depending on the end that is
used to attach to. This bracket can be replaced by simply
using two standard brackets at the union. |
|
 |
|
|
|
X-Y System
The X-Y Gate is used to join one track to ride on two
other tracks, giving a lift the full virtual range of the
square the
tracks cover. This application is mostly found in
hospitals or medical facility as they service many
different size patients. |
|
 |
|
|
|
1/4 Shim
The 1/4 Shim is used to space brackets as nearly all
ceilings are not perfectly flat or flush. |
|
 |
|
|
|
1/8 Shim
The 1/8 Shim is used to space brackets as nearly all
ceilings are not perfectly flat or flush.
|
|
 |
